hi i am new to this forum and vaping since 7 8 months.. i bought my first rda ida rda.. its air canal width 1.5 mm (mtl kit on) and have a lot 24 ss and 26 twisted kanthal wires. can i build an efficient coil with those wires without burning the cotton.. i am vaping mouth to lung inhale with my rda a few days ago and i have griffin 25 taf
mtl type rda tank and coil build
- Thread starter broncotr
- Start date
- th_trl_thread_readers 0
- Status
thank you for quick answer but they heat late and cool late i am vaping via very thin air channel 1.5 mm. can you suggest me a build type how many wrap on which mm
Whay i build. Id 2 mm diameter 8 wraps 26 gauge kanthal puts me at .78-.83 ohm. Single coil can go 15 watts without burning the cotton. If you go dual coils at 30 watts or so
first image for ss wire 24 awg second is 26 twisted kanthal and for at least to make it 0.7 ohm what do you say bro
i tried these but heating is too much for restricted air flow i think i want miraclous coil 
Welcome and glad you joined. 7-8 months will give you a good background in vaping. You may profit/benefit by investing a little more study and research with regards to how various coil material, shapes of, and wicking interact to form the total vaping experience.
Might like to read:
Guide For New Vapers | Spinfuel VAPE
Efficiency. Thinner wire and higher resistance VS thick wire and lower resistance
Learn About Vaping Here - Everything Ecigs - From Beginner To Advanced
If you have the funds switch to a smaller rta. Tough you can mtl sub ohm builds. Your battery will last longer using higher ohm builds let's say with 28g or 30g kanthal. You might not find it satisfying as and have to up nicotine strength. But ramp up time and juice consumption should go down. As for burning your coils proper wicking is key.
I prefer 30ga wire, 6-7 wraps, open coil, 2mm id. About 1.5-1.8 ohms. Fire at 8 watts. Heats up and cools quickly.
My preference exactly. Works equally well for me on on my KFL+ or my RM2 on the Reo. IMO you really need a RDA/RTA with a small chamber for good MTL vaping. If you can find a Kayfun Lite Plus (or a clone) that would get my vote for a tank. The Mini V3 should be currently available and would also be a good choice for MTL. For an RDA I'd recommend any small chamber from the little $4 ones on Fasttech to whatever you are willing to spend. I have had good results from an O-16 clone on a Pico Squeeze. The O-16 came with a spare solid positive pin if you don't need bottom feed.
i tried 6 wraps 2.5 mm 28 g. good but quick heats means we could not draw long?? then i tried parallel 3 mm 6 wraps 28g. aroma is good but there is rump up time a little bit
1.5 mm air width after griffin you think my first mtl and rda experince is this..
at mtl vaping my thorax exhausting.. do we draw via our cheeks? and do we draw hard? because normally says no hard drawing
my first mtl and rda experince is this..
for MTL you'll need higher gauge wire most likely. it'll be tough (not impossible) to get a good MTL with those wires, on that atomizer. (my opinion of course)
for most of my MTL stuff, I prefer 28 gauge kanthal or 30 gauge SS
for most of my MTL stuff, I prefer 28 gauge kanthal or 30 gauge SS
What was your final resistance?
How many watts did you feed it?
How did it vape?
Cheers
I
1.19 ohm 11 watt good but not enough .. at my griffin 6 mg fairly enough..nicotine is this 12 mg.. but for mtl vape i couldnt like paralel or twisted so i will go on like these coils maybe i will try 26 g 2.5 mm 6 7 wraps
i am curious and dont know truly do we hard draw on mtl vaping or like dl vaping smooth draw... 1.5 mm air canal i am exhausthing or do we use cheeks muscles
MTL is like smoking a cigar or normal cigarette.
DTL is strong, long and deep. A bit like sucking the helium from an inflated balloon.
Check out Utube for some examples.
MTL: Igetch69,
DTL: the vapingbogan.
Cheers
I
- Status
Similar threads
- Locked
