eBaron Dripper RBA?? (vs Fatty V2???)

[Quoiyaien]

Hey Guys,

As some of you know, i have been looking for a rebuildable dripping atomizer, and i happened upon an eBaron... just wondering if anyone here has used one, and what your thoughts are?

Right now im debating between a Fatty V2 or the eBaron dripper by Leo...

The plus of the eBaron is that it is super easy to rebuild, but needs no resistance wire for the process..

the fatty also looks not as easy, but not hard either (im good with small electronics) but doesnt need no resistance wire...

Any one have any thoughts on the this? I have decided that I am basically going to buy a provari, and the eBaron pro looks awesome on it...

The thing about the fatty that concerns me a bit is that the wick is raised up off the floor, and there is a slight concave for the juice... I feel like that could potentially create a mess... (anyone ever had leaking issues with a fatty?)

Anyway, thanks for the input!

Cheers!

 

[Thrasher]

never tried the fatty, lot of people like it it is a side vent right? the only problem with leaking would be overfilling or tilting it so juice can leak out the hole. and just making a slightly longer wick will act as a well for the bottom.

the baron pro is center bottom feed for air and i like the raised ceramic cup so leaking only comes from severe overfilling. i bough a pack of the replacement coils just to have extra ceramics, rebuilding with NR wire can be a pain but not hard, i did spot a post where someone has success using just resistance wire so i will try that when the time comes to redo it. the guy near work has the spiral (same thing without ProV base) and let me try it and powee the thing vapes like a broken fire extinguisher so i been waiting for them to restock ever since, the pre oreders are almost full so if you dont hurry the only choice will be the fatty.

eBaron Dripper Pro

 

[Quoiyaien]

Ok well I just bought the eBaron... guess im committed to buying that provari now... lol

 

[Quoiyaien]

Anyone have any thoughts to share on the ebaron?

You know how it is... you order something, then obessively read/watch about it until it arrives... problem is, there arent very many youtube vids, and I read all the threads on the UK vapers forum...

So?

 

[montara]

I love my Fatty, have 3 of 'em and yes they can be messy. I had been getting sever leakage out the air holes until i tailed the wick down and under the coil. This not only soaked up juice off the bottom, it prevents coil from shorting on center pin. Fatty is my go-to, all day chain vape piece .
What I really like about the Fatty (other than awesome flavor and vapor) is that it's future proof, wick and wire is all you'll ever need.
As far as set up, wrap 4 on 7/23 drill bit and screw down. Test fire's @ 2.6. Then I use a hybrid wick of 7/8 #500 mesh rolled tight then covered with Omega XS-116 braided sleeve. Slide it in the coil and enjoy.
The eBarron looks like a great piece but I just can't sign up for a ViVi style RBA.

 

[Thrasher]

woo hoo my pro will be here in a few days yay.

The eBarron looks like a great piece but I just can't sign up for a ViVi style RBA

huh? its a dripper how did you see a viv setup here? except for the ceramic cup it works just like any of the stem feed drippers.

 

[Quoiyaien]

The eBarron looks like a great piece but I just can't sign up for a ViVi style RBA.

Check out these vids:
REVIEW OF THE eBARON DRIPPING ATOMISER FOR ELECTRONIC CIGARETTES - YouTube


It has nothignt o do with the vivi... it doesnt have a tank, its just a dripper.. Are you saying vivi style because of the silica wick? The fatty has essentially the same build... However I do believe the eBaron holds a bit more juice.. (still want a fatty v2 mind you... im just curious why you think that about the eBaron?

Cheers!

 

[Abracastabya]

I just ordered one as well...stoked!