Jigsaw juice shaker

[SLIPPY_EEL]

I saw a vid someone posted a long tome ago of a paint shaker, so i decided to dig out the jigsaw and make my own juice shaker, this wire ive used is whats used for fixing steel bar's together on building sites but i dont see why you cant use a coat hanger, it would be easier to form your bottle holder.
Its easier to grab somthing from around the house about the same diameter as the base of your bottle and something the diameter of the neck of the bottle, you will just squash your juice bottle if you try to use that to shape your wire.
It doesnt have to be perfect, so long as you can put your bottle in, i put my bottle in upside down, then the wire will sit in the groove between the bottle neck and the cap, stopping it from flying out.
This was my first attempt at making it, i started out with about 18inches of wire that i bent in half, i started by shaping the middle part that hold the side of the bottle, then the loop parts and then shaped and cut the the legs even.





as you can see this juice has been thorouly shaken not stirred

hope it helps out anyone else that gets fed up with a sore arm from juice shaking!

its really easy, but if anyone needs help just ask

 

[samwest]

Ingenuity. Good job. Filed for future consideration.

 

[Kashief]

Pretty impressive! I have a huge quart bottle of VG my lady surprised me with and I've used it to give my store bought juice some good vapor production. You have no idea how handy this would be (actually you do lol)... after getting the VG into a 30ml bottle I just stick into the foil seal of the VG container, squeezing that into the smaller 10ml bottles kills the moral of thumb muscle and then my arm just says "Nope...screw you buddy, I'm done!"...lol so ...all because I refuse to buy more syringes until I find the pack that the gremlins took!

Sent from my Venue 8 Pro 5830 using Tapatalk

 

[SLIPPY_EEL]

Pretty impressive! I have a huge quart bottle of VG my lady surprised me with and I've used it to give my store bought juice some good vapor production. You have no idea how handy this would be (actually you do lol)... after getting the VG into a 30ml bottle I just stick into the foil seal of the VG container, squeezing that into the smaller 10ml bottles kills the moral of thumb muscle and then my arm just says "Nope...screw you buddy, I'm done!"...lol so ...all because I refuse to buy more syringes until I find the pack that the gremlins took!

Sent from my Venue 8 Pro 5830 using Tapatalk

it's surprising how watery VG will go if you pop it into hot water, when i want to add VG to anything i pour it into a glass first, then use a 30ml syringe with a bit of tube on the end so you can get to the bottom of the glass.
My juice's are quite high in VG, i hate waiting for it to drip out the end of the bottle tip so i took a 1/16 drill bit and bored out the hole in the bottle tip, just watch if you try to do this that you dont hold the plastic tip with your hand while your drilling, you can either break through the plastic and it will spin, cutting your hand or you will go straight through and puncture your hand, pliars are good

 

[Kashief]

I considered that. And I can admit, I'm usually in a rush lol... however... I put it in my pocket and since its so hot lately, it loosened it up a bit! But I did happen to find a few 30ml bottles with the fat tips that are open enough to squirt VG easily as I was reading this. And as for widening the tips for easy flow, a hot small screwdriver or pin vise bit helps too!

And believe it or not, this all fits, neatly, into this makeshift cape case lol.


Sent from my Venue 8 Pro 5830 using Tapatalk

Sent from my Venue 8 Pro 5830 using Tapatalk

 

[ed101z]

Thanks. I'll try this when I get my new order. It'll definitely help mixing those big 100ml bottles with perfection.

 

[SLIPPY_EEL]

No problems guys/gals, have fun watching your juice bottle in two places at the same time