A while back I got in my vape mail a total of 8 Newest Generation
Stainless Steel CE5-S BDCC (Bottom Dual Coil Changeable) Clearomizer ...
The Best of the Best...
Except for one thing... like many other clearomizers... sold by Suppliers....
without a decent FIX IT IDEA????
NONE OF THEM could or would
make contact (their pins were just to far up inside the base of tanks clearomizer)
away from the deep well contact POST of my MVP 2.0, and even my Vision Spinners contact posts.
I really didn't think to much of or about it... I just got me my trusty SPOOL of THREAD
Opened up the bottom (base) of each CE5-S Clearomizer... Took out their coil (aka heads)...
(See pictures)
Then Completely... Pulled the PINS out of each and every single one of them
Wrapped 12 TURNS of thread around the back of each Pin...
AFTER making sure to tie knots... used finger nail clips to cut the thread
Used my finger nail (thumb) to pack ...just a little push... of the thread against the back of the pin...
Put the pins back where they belonged... And that was the total of the FIX IT!
NOTE: You really don't have to take (the pins) them all the way out
to wrap the thread around them... I do it either way...
View attachment 282937View attachment 282939
NOTE: Those pins are small... so watch out for the SOCK MONSTER...
the pins have a way of getting away from you. gulp!!! If they fall out just put them back.
Then I just put the now threaded HEAD... (aka the coil) back in each of the CE5-S Clearomizers
and to this day vaping away.... NO contact problems at all....
I use this procedure with other CLEAROS such as vivi Novas etc... also...
YES!.... You can do this to TOP COILS aka heads also...
and they will push the PIN at the bottom of the clearomizer down.
Again... There has yet to be any of the experts recording a VIDEO about
this simple CONTACT PIN FIX IT problem... You now know before them... go for it!
Stainless Steel CE5-S BDCC (Bottom Dual Coil Changeable) Clearomizer ...
The Best of the Best...
Except for one thing... like many other clearomizers... sold by Suppliers....
without a decent FIX IT IDEA????
NONE OF THEM could or would
make contact (their pins were just to far up inside the base of tanks clearomizer)
away from the deep well contact POST of my MVP 2.0, and even my Vision Spinners contact posts.
I really didn't think to much of or about it... I just got me my trusty SPOOL of THREAD
Opened up the bottom (base) of each CE5-S Clearomizer... Took out their coil (aka heads)...
(See pictures)
Then Completely... Pulled the PINS out of each and every single one of them
Wrapped 12 TURNS of thread around the back of each Pin...
AFTER making sure to tie knots... used finger nail clips to cut the thread
Used my finger nail (thumb) to pack ...just a little push... of the thread against the back of the pin...
Put the pins back where they belonged... And that was the total of the FIX IT!
NOTE: You really don't have to take (the pins) them all the way out
to wrap the thread around them... I do it either way...
View attachment 282937View attachment 282939
NOTE: Those pins are small... so watch out for the SOCK MONSTER...
the pins have a way of getting away from you. gulp!!! If they fall out just put them back.
Then I just put the now threaded HEAD... (aka the coil) back in each of the CE5-S Clearomizers
and to this day vaping away.... NO contact problems at all....
I use this procedure with other CLEAROS such as vivi Novas etc... also...
YES!.... You can do this to TOP COILS aka heads also...
and they will push the PIN at the bottom of the clearomizer down.
Again... There has yet to be any of the experts recording a VIDEO about
this simple CONTACT PIN FIX IT problem... You now know before them... go for it!
